No Tags Found!


amin_mech03
3

Dear All,
My name is Amin and now, I am working as technical scaffold engineering. Any one know how to calculate the load on scaffold? and the permitted maximum high of the scaffold.
Thanks
regards
Amin

From Indonesia, Jakarta
raghuvaran chakkaravarthy
497

Dear Amin,
Warm welcome to our Citehr EHS forum. Earlier we discussed against scaffold calculation u can get scaffolding related data’s from earlier thread (please go by below mentioned link) but we are not get final soluction.Anyhow I hope you get soluction.Keep on participate share & gain your knowledge from our forum. . .
https://www.citehr.com/304872-scaffo...#axzz1A4KGfawq
Thanks & Besafe
Raghu

From United States, Fpo
hseofficerjsk
29

Dear friend
all scaffolding height is determined by using height to base ratio that is 4:1 .this means height can up to 4 times the minimal base width .
For example a scaffolding having minimal base width of 2 metere its height can have up to 8 metre
regarding load
there are three types of scaffolding
1 light duty which can have up to 120kg/squrem
2 medium duty which can have up to 240kg/squrem
3 heavy or special duty above 240kg/squrem

From India, Thrissur
hseofficerjsk
29

And one more thing regarding height is due to wind factor
height of tower scaffolding out side the building height to base ratio is 3.5 :1
mobile scaffolding due to wind factor height out side building is 3:1
this diffrence is to protect the scaffolding from heavy wind

From India, Thrissur
gt.sreekanth
2

My name is SHAN and now, I am working as technical scaffold engineering. Any one know how to calculate the Materials for scaffold? Its for bridges.
From India, Hyderabad
Kesava Pillai
252

Dear Friends

THE LAW REQUIRES THAT NO SCAFFOLD SHALL BE ERECTED, MOVED, DISMANTLED OR ALTERED EXCEPT UNDER THE DIRECT SUPERVISION OF A COMPETENT PERSON.

Scaffolding is a specialization.

There are more than 30 different types of scaffolds. Scaffold can be supported, under-hung , hanging or bracket supported.

Materials used are bamboo, aluminium, fiberglass and steel.

Common scaffold are tube and coupler, system and welded frame. Welded frame scaffold are only for light duty.

OSHA standards which are widely adopted give the load capacities which are already given by hseofficerjsk.

Details on ground preparation, sole boards, base plates, Post spacing, bracing requirements, guard rails and toe boards are all given in the standards for light duty and medium duty scaffolds.

With prescribed post spacing the scaffold height in this case can be up to 125 feet.

Only for independent, tower and mobile scaffolds the 1:4 (1 base width to 4 height) ratio is applicable. You can increase the height of scaffolds by using suitable ties, gay wires and rakers. However this is applicable for scaffold up to a height of 40 feet. Beyond this height the scaffold should be designed by a structural engineer.

Heavy duty scaffold should only be designed by a structural engineer. There can be dead load and live load on scaffold. Though the construction method is same, post spacing and bracing will differ depending up on loads.

Weight of all the scaffold components plus the intended load will have to be considered in assessing the load on a scaffold. A factor of safety of 4 is required for any scaffold.

Regards,

Kesava Pillai

From India, Kollam
asudhir17
1305

Although bamboo is accepted, many organisations have banned use of bamboo. In our company we make steel pipes with couplers compulsory for scaffolds. Thanks and Regards, Sudhir
From India, Nasik
pon1965
604

It is advisable to refer the recommendations of scaffold manufacturers for the design load.
Refer the below link to know more about scaffold
Scaffold Handbook
Pon

From India, Lucknow
vamsi256
6

Hi can anyone provide info if we can use binding wire for tieing up planks and if so what should be the dia of the binding wire thanks and regards vamsi akunuri
From India, Vadodara
raghuvaran chakkaravarthy
497

Hi Vamsi,
See the animation picture if something happens like that TIEWIRE can hold the planks??
I don’t have scaffolding IS standard some of our members can help you on IS standard.

[IMG]http://www.osha.gov/SLTC/etools/scaffolding/images/bend4.gif[/IMG]

From United States, Fpo
Community Support and Knowledge-base on business, career and organisational prospects and issues - Register and Log In to CiteHR and post your query, download formats and be part of a fostered community of professionals.






Contact Us Privacy Policy Disclaimer Terms Of Service

All rights reserved @ 2024 CiteHR ®

All Copyright And Trademarks in Posts Held By Respective Owners.